Elko eLAN-RF-003 Manuál s instrukcemi stáhnout pdf (Strana 33)

60mm

21mm

RFDEL-71B

V L N S

LED, ESL, R

Description of the device

Connection

serves for controlling light intensity of these light sources:

the type of light source is set by the switch on the front of the of the device

max. output load is 160 W

option of controlling existing external button and RF transmitter

electronic overcurrent and thermal protection - switches o the output in case of overload,

short circuit or overheating

setting min. brightness by potentiometer on the front of the device eliminates  ashing of various types of light sources

by installing the actuator under an existing button, you have the option of further control of lighting using RF

Control wireless transmitters or the RF Touch touch screen unit. This then makes it possible to control the actuator

with the existing button or wireless controller

the actuator can be controlled by up to 32 channels

6 light functions, ON/OFF function (identical with the functions of RFDA-71B) see p. 32

Technical parameters

CONTROL

ELEMENTS

EAN code

8595188145121

230 V AC / 50 Hz

1.1 VA

0.8 W

+10/ -15 %

4-wire, with “NEUTRAL“

R,L,C, LED, ESL

2 x MOSFET

160 W*

868 MHz

up to 160 m (more on range on p. 44)

button PROG (ON/OFF), external button

-20 up to + 35°C

-30 up to +70°C

any*

free at lead-in wires

IP 30 under normal conditions

III.

4 x 0.75 mm

90 mm

49 x 49 x 21 mm

40 g

EN 607 30-1 ED.2

Supply voltage:

Apparent power:

Dissipated power:

Supply voltage tolerance:

Connection:

Dimmed load:

Output

Contactless:

Load capacity:

Controlling

RF command from the transmitter:

Range in open space:

Manual control:

Glow lamp connection:

Further data

Operating temperature:

Storage temperature:

Operating position:

Mounting:

Protection:

Overvoltage category:

Contamination degree:

Terminals (CY wire, Cross-section):

Terminal length:

Dimensions:

Weight:

Related standards:

* capacity for power factor cos φ=1

The power factor of dimmable LEDs and ESL bulbs ranges from cos φ = 0.95 up to 0.4.

An approximate value of maximum load may be obtained by multiplying the load capacity of the

dimmer by the power factor of the connected light source.

Controlling the dimmer:

! a short press of the button (< 0.5s) switches light on or o

! a long press (> 0.5s) enables  uid regulation of light intensity

! for the ESL load, when the lamp is switched off, a short press increases the brightness to the maximum level (when the

energy saver „lights up“) and then drops to the preset level

Setting the minimum brightness:

! performed using the potentiometer on the front side

! used mainly when dimming energy-saving  uorescent tubes and LED bulbs due to their di ering illumination characteristics

! it prevents unwanted  ashing when setting the actuator to the min. brightness

Description of function

External button

Neutral conductor

Output to appliance

Phase conductor

Potentiometer for setting

minimum brightness

Button

Prog

source type symbol description

resistive

resistive bulb, halogen lamp

inductive

inductive coil transformer for low-voltage halogen lamps

capacitive

electronic transformer (capacitive load) for low-voltage halogen lamps LED

LED

LED lamps and LED light sources, 230 V

ESL

dimmable energy-saving tubes

coil transformer

electronic transformer

RF receiver: Universal dimming actuator RFDEL-71B

Switch for selecting

the light source

Device status

indication

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 51 52

Komentáře k této Příručce

Žádné komentáře

Elko eLAN-RF-003 Manuál s instrukcemi Strana 33

Komentáře k této Příručce